peddy 0.4.8

Fast Pedigree::VCF QC

peddy compares familial-relationships and sexes as reported in a PED/FAM file with those inferred from a VCF.

It samples the VCF at about 25000 sites (plus chrX) to accurately estimate relatedness, IBS0, heterozygosity, sex and ancestry. It uses 2504 thousand genome samples as backgrounds to calibrate the relatedness calculation and to make ancestry predictions.

It does this very quickly by sampling, by using C for computationally intensive parts, and by parallelization.

If you use peddy, please cite Pedersen and Quinlan, Who’s Who? Detecting and Resolving Sample Anomalies in Human DNA Sequencing Studies with Peddy, The American Journal of Human Genetics (2017), http://dx.doi.org/10.1016/j.ajhg.2017.01.017

Note that somalier is a more scalable, faster, replacement for peddy that uses some of the same methods as peddy along with some new ones.

Quickstart

See installation below.

Most users will only need to run as a command-line tool with a ped and VCF, e.g:

python -m peddy -p 4 --plot --prefix ceph-1463 data/ceph1463.peddy.vcf.gz data/ceph1463.ped

This will use 4 cpus to run various checks and create ceph-1463.html which you can open in any browser to interactively explore your data.

It will also create create 4 csv files and 4 QC plots. These will indicate:

• discrepancies between ped-reported and genotype-inferred relations
• discrepancies between ped-reported and genotype-inferred sex
• samples with higher levels of HET calls, lower depth, or more variance in b-allele-frequency (ref / (ref + alt )) for het calls.
• an ancestry prediction based on projection onto the thousand genomes principal components

Finally, it will create a new file ped files ceph1463.peddy.ped that also lists the most useful columns from the het-check and sex-check. Users can first look at this extended ped file for an overview of likely problems.

See the docs for a walk-through and thorough explanation of each plot.

hg38 or custom sites

By default, peddy uses hg19/GRCh37. It can be forced to use sites for hg38 by passing --sites hg38. To create custom sites, have a look at the sites files included with peddy along with the corresponding .bin.gz which is just the raw binary alternate counts (gt_types) from thousand-genomes that have been written as uint8 and gzipped.

Speed

Because of the sampling approach and parallelization, peddy is very fast. With 4 CPUs, on the 17-member CEPH1643 pedigree whole-genome VCF, peddy can run the het-check and PCA in ~ 8 seconds. The pedigree check comparing all vs. all samples run in 3.6 seconds. It finishes the full set of checks in about 20 seconds.

In comparison KING runs in 14 seconds (it is extremely fast); the time including the conversion from VCF to binary ped is 85 seconds.

On larger datasets, with hundreds or thousands of samples, it can be beneficial to add as many cores as possible; for smaller datasets with dozens of samples about 4 processors reduces the computation time as much as 8 or more would.

Validation

The results between peddy and KING are comparable, but peddy does better on cohorts where most samples are related. See the figure below where the peddy relatedness estimate is closer to the actual than KING which over-estimates relatedness.

Peddy uses the KING algorithm for calculating relatedness and so they match quite well. Peddy also runs PCA on the 2504 samples from 1000 genomes, then fitting an SVM and predicting ancestry in addition to calculating relatedness among all pairwise combinations of the 17 samples.

Warnings and Checks

On creating a pedigree object (via Ped('some.ped'). peddy will print warnings to STDERR as appropriate like:

pedigree warning: '101811-101811' is dad but has female sex
pedigree warning: '101897-101897' is dad but has female sex
pedigree warning: '101896-101896' is mom of self
pedigree warning: '102110-102110' is mom but has male sex
pedigree warning: '102110-102110' is mom of self
pedigree warning: '101381-101381' is dad but has female sex
pedigree warning: '101393-101393' is mom but has male sex

unknown sample: 102498-102498 in family: K34175
unknown sample: 11509-11509 in family: K567331
unknown sample: 5180-5180 in family: K8565

Installation

Conda

Nearly all users should install using conda in the anaconda python distribution. This means have your own version of python easily installed via:

INSTALL_PATH=~/anaconda
wget http://repo.continuum.io/miniconda/Miniconda2-latest-Linux-x86_64.sh
# or wget http://repo.continuum.io/miniconda/Miniconda2-latest-MacOSX-x86_64.sh
bash Miniconda2-latest* -fbp $INSTALL_PATH
PATH=$INSTALL_PATH/bin:$PATH

conda update -y conda
conda config --add channels bioconda

conda install -y peddy

This should install all dependencies so you can then run peddy with 4 processes as:

python -m peddy --plot -p 4 --prefix mystudy $VCF $PED

Github

git clone https://github.com/brentp/peddy
cd peddy
pip install -r requirements.txt
pip install --editable .

run with

peddy --plot -p 4 --prefix mystudy $VCF $PED